[1]张耀春,于海丰,张文元,等.焊接工字形钢支撑等幅轴向反复循环荷载下低周疲劳性能试验[J].东南大学学报(自然科学版),2009,39(3):525-530.[doi:10.3969/j.issn.1001-0505.2009.03.020]
 Zhang Yaochun,Yu Haifeng,Zhang Wenyuan,et al.Experimental study on low-cycle fatigue behavior of welded I-section steel bracing members under constant amplitude reversed cyclic axial loading[J].Journal of Southeast University (Natural Science Edition),2009,39(3):525-530.[doi:10.3969/j.issn.1001-0505.2009.03.020]
点击复制

焊接工字形钢支撑等幅轴向反复循环荷载下低周疲劳性能试验()
分享到:

《东南大学学报(自然科学版)》[ISSN:1001-0505/CN:32-1178/N]

卷:
39
期数:
2009年第3期
页码:
525-530
栏目:
土木工程
出版日期:
2009-05-20

文章信息/Info

Title:
Experimental study on low-cycle fatigue behavior of welded I-section steel bracing members under constant amplitude reversed cyclic axial loading
作者:
张耀春1 于海丰1 张文元1 连尉安2
1 哈尔滨工业大学土木工程学院, 哈尔滨 150090; 2 上海建筑设计研究院有限公司, 上海 200041
Author(s):
Zhang Yaochun1 Yu Haifeng1 Zhang Wenyuan1 Lian Wei’an2
1 School of Civil Engineering, Harbin Institute of Technology, Harbin 150090, China
2 Shanghai Institute of Architectural Design and Research Co. Ltd., Shanghai 200041, China
关键词:
焊接工字钢支撑 低周疲劳性能 循环荷载
Keywords:
welded I-section steel bracing member low-cycle fatigue behavior cyclic loading
分类号:
TU391;TU317.1
DOI:
10.3969/j.issn.1001-0505.2009.03.020
摘要:
在两端铰接ST12材质焊接工字形钢支撑等幅轴向反复循环荷载低周疲劳性能试验基础上,进行了Q235材质焊接工字形钢支撑低周疲劳性能试验.分析了2种材质的共47根支撑在试验载荷下的最大横向变形和最大抗压承载力特性,验证了文献及规范方法的可靠性.在假设加载幅值、试件几何特征以及钢材屈服强度对支撑低周疲劳寿命影响相互独立的基础上,提出了估算支撑低周疲劳寿命的经验公式.分析表明,翼缘宽厚比越小,长细比越大,加载幅值越小,屈服强度越低,支撑低周疲劳寿命越高.由于在地震作用时支撑构件位移时程不可预知,设计支撑时除应严格限制翼缘板件宽厚比外,还应适当采用低屈服点钢材及适当放宽某些现行规程对长细比的限制,以避免支撑过早断裂.最后,根据支撑不同损伤阶段的累积耗能比,指出可偏于安全的采用阶段Ⅰ的寿命估算公式来预估支撑的低周疲劳寿命.
Abstract:
Based on the low-cycle fatigue behavior tests of welded I-section ST12 steel bracing members with pinned connections under constant amplitude reversed cyclic axial loading, the low-cycle fatigue behavior of welded I-section Q235 steel bracing members with pinned connections was examined. The test results about the maximum lateral deformation and the maximum compressive strength of 47 bracing members made of Q235 and ST12 were studied and verified in comparison with the results calculated by the relevant literatures or codes. According to the assumption that the geometry properties, loading amplitude and steel yield strength are independent of each other for estimating the low-cycle fatigue life, some empirical formulas are presented. It is found that the low-cycle fatigue life increases with the decrease in the width-thickness ratio of the flanges, the increase in the brace slenderness ratio, and the decrease in the loading amplitude and yield strength of the bracing members. Because the displacement histories of the bracing members can not be predicted during an earthquake, in order to avoid early fractures of the bracing members, besides limiting the width-thickness ratio of the flanges, low yield strength steel should be adopted and the brace slenderness ratio limitation in some current codes should be relaxed. Finally, based on the energy index ratios for different damage stages, it is proposed that the low-cycle fatigue life of brace members can be safely predicted by the empirical formulas for stage Ⅰ.

参考文献/References:

[1] Rai D C,Goel S C.Seismic evaluation and upgrading of chevron braced frames [J].Journal of Constructional Steel Research,2003,59(8):971-994.
[2] Elchalakani M,Zhao X L,Grzebieta R.Test of cold-formed circular braces under cyclic axial loading [J].Journal of Structural Engineering,2003,129(4):507-514.
[3] Zhao X L,Grzebieta R,Lee C.Void-filled cold-formed rectangular hollow section braces subjected to large deformation cyclic axial loading [J].Journal of Structural Engineering,2002, 128(6):746-753.
[4] Shaback B,Brown T.Behavior of square hollow structural steel braces with end connections under reversed cyclic axial loading[J].Canadian Journal of Civil Engineering,2003,30(8):745-753.
[5] Tremblay R,Archambault M H,Filiatrault A.Seismic response of concentrically braced steel frames made with rectangular hollow bracing members [J].Journal of Structural Engineering,2003,129(12):1626-1636.
[6] Brodericka B M,Gogginsa J M,Elghazoulib A Y.Cyclic performance of steel and composite bracing members [J]. Journal of Constructional Steel Research,2005,61(5):493-514.
[7] 张耀春,连尉安,张文元.焊接工字形截面钢支撑低周疲劳性能试验研究[J].建筑结构学报,2005,26(6):114-121.
  Zhang Yaochun,Lian Weian,Zhang Wenyuan.The low-cycle fatigue tests of welded I-section bracing members[J].Journal of Building Structures,2005,26(6):114-121.(in Chinese)
[8] 连尉安.焊接工字形钢支撑低周疲劳性能及其应用研究 [D].哈尔滨:哈尔滨工业大学土木工程学院,2006.
[9] Zhang Y H,Lian W A,Zhang W Y.Factors affecting the low cyclic fatigue behavior around the weak axis of welded I-section bracing members[C] //Proceedings of the International Conference on Fracture and Damage Mechanics.Harbin,China,2006:959-962.
[10] 方开泰.均匀设计与均匀设计表[M].北京:科学出版社,1994.
[11] European Committee for Standardization.EN1993-1-1 EC3 Design of steel structures-part1-1:general rules and rules for buildings[S].Brussels:European Committee for Standardization,2003.
[12] Tremblay R.Inelastic seismic response of steel bracing members [J]. Journal of Constructional Steel Research,2002,58(6):665-701.
[13] 中华人民共和国建设部.GB 50017—2003 钢结构设计规范[S].北京:中国计划出版社,2003.
[14] American Institute of Steel Construction.AISC360—05 Specification for structural steel buildings [S].Chicago:AISC Committee,2005.
[15] 中华人民共和国建设部.GB 50011—2001 建筑抗震设计规范[S].北京:中国建筑工业出版社,2002.
[16] 中华人民共和国建设部.JGJ 99—98 高层民用建筑钢结构技术规程[S].北京:中国建筑工业出版社,1998.

备注/Memo

备注/Memo:
作者简介: 张耀春(1937—),男,教授,博士生导师,Ych_Zhang@163.com.
基金项目: 国家自然科学基金“九五”重大资助项目(59895410)、国家科技支撑计划资助项目(2006BAJ01B02-01-04).
引文格式: 张耀春,于海丰,张文元,等.焊接工字形钢支撑等幅轴向反复循环荷载下低周疲劳性能试验[J].东南大学学报:自然科学版,2009,39(3):525-530. [doi:10.3969/j.issn.1001-0505.2009.03.020]
更新日期/Last Update: 2009-05-20